Vai al contenuto

Risoluzione dei problemi CANBUS

Questo documento fornisce informazioni sulla risoluzione dei problemi di comunicazione quando si utilizza Klipper with CAN bus.

Verificare la connessione CAN bus

Il primo passo nella risoluzione dei problemi di comunicazione è verificare il cablaggio del CAN bus.

Be sure there are exactly two 120 Ohm terminating resistors on the CAN bus. If the resistors are not properly installed then messages may not be able to be sent at all or the connection may have sporadic instability.

The CANH and CANL bus wiring should be twisted around each other. At a minimum, the wiring should have a twist every few centimeters. Avoid twisting the CANH and CANL wiring around power wires and ensure that power wires that travel parallel to the CANH and CANL wires do not have the same amount of twists.

Verify that all plugs and wire crimps on the CAN bus wiring are fully secured. Movement of the printer toolhead may jostle the CAN bus wiring causing a bad wire crimp or unsecured plug to result in intermittent communication errors.

Check for incrementing bytes_invalid counter

The Klipper log file will report a Stats line once a second when the printer is active. These "Stats" lines will have a bytes_invalid counter for each micro-controller. This counter should not increment during normal printer operation (it is normal for the counter to be non-zero after a RESTART and it is not a concern if the counter increments once a month or so). If this counter increments on a CAN bus micro-controller during normal printing (it increments every few hours or more frequently) then it is an indication of a severe problem.

Incrementing bytes_invalid on a CAN bus connection is a symptom of reordered messages on the CAN bus. There are two known causes of reordered messages:

  1. Old versions of the popular candlight_firmware for USB CAN adapters had a bug that could cause reordered messages. If using a USB CAN adapter running this firmware then make sure to update to the latest firmware if incrementing bytes_invalid is observed.
  2. Some Linux kernel builds for embedded devices have been known to reorder CAN bus messages. It may be necessary to use an alternative Linux kernel or to use alternative hardware that supports mainstream Linux kernels that do not exhibit this problem.

Reordered messages is a severe problem that must be fixed. It will result in unstable behavior and can lead to confusing errors at any part of a print.

Obtaining candump logs

The CAN bus messages sent to and from the micro-controller are handled by the Linux kernel. It is possible to capture these messages from the kernel for debugging purposes. A log of these messages may be of use in diagnostics.

The Linux can-utils tool provides the capture software. It is typically installed on a machine by running:

sudo apt-get update && sudo apt-get install can-utils

Once installed, one may obtain a capture of all CAN bus messages on an interface with the following command:

candump -tz -Ddex can0,#FFFFFFFF > mycanlog

One can view the resulting log file (mycanlog in the example above) to see each raw CAN bus message that was sent and received by Klipper. Understanding the content of these messages will likely require low-level knowledge of Klipper's CANBUS protocol and Klipper's MCU commands.

Parsing Klipper messages in a candump log

One may use the tool to parse the low-level Klipper micro-controller messages contained in a candump log. Using this tool is an advanced topic that requires knowledge of Klipper MCU commands. For example:

./scripts/ mycanlog 108 ./out/klipper.dict

This tool produces output similar to the parsedump tool. See the documentation for that tool for information on generating the Klipper micro-controller data dictionary.

In the above example, 108 is the CAN bus id. It is a hexadecimal number. The id 108 is assigned by Klipper to the first micro-controller. If the CAN bus has multiple micro-controllers on it, then the second micro-controller would be 10a, the third would be 10c, and so on.

The candump log must be produced using the -tz -Ddex command-line arguments (for example: candump -tz -Ddex can0,#FFFFFFFF) in order to use the tool.

Using a logic analyzer on the canbus wiring

The Sigrok Pulseview software along with a low-cost logic analyzer can be useful for diagnosing CAN bus signaling. This is an advanced topic likely only of interest to experts.

One can often find "USB logic analyzers" for under $15 (US pricing as of 2023). These devices are often listed as "Saleae logic clones" or as "24MHz 8 channel USB logic analyzers".


The above picture was taken while using Pulseview with a "Saleae clone" logic analyzer. The Sigrok and Pulseview software was installed on a desktop machine (also install the "fx2lafw" firmware if that is packaged separately). The CH0 pin on the logic analyzer was routed to the CAN Rx line, the CH1 pin was wired to the CAN Tx pin, and GND was wired to GND. Pulseview was configured to only display the D0 and D1 lines (red "probe" icon center top toolbar). The number of samples was set to 5 million (top toolbar) and the sample rate was set to 24Mhz (top toolbar). The CAN decoder was added (yellow and green "bubble icon" right top toolbar). The D0 channel was labeled as RX and set to trigger on a falling edge (click on black D0 label at left). The D1 channel was labeled as TX (click on brown D1 label at left). The CAN decoder was configured for 1Mbit rate (click on green CAN label at left). The CAN decoder was moved to the top of the display (click and drag green CAN label). Finally, the capture was started (click "Run" at top left) and a packet was transmitted on the CAN bus (cansend can0 123#121212121212).

The logic analyzer provides an independent tool for capturing packets and verifying bit timing.

Torna su